bruce-zhou-avator-600x600

Written by Bruce Zhou
Founder & Managing Director | JOTA Machinery
Paper converting machinery specialist since 2002.
Connect with me on LinkedIn
Published: 19,October, 2026
Last Updated: 19,October, 2026 13:41:08 PM GMT+8

A batch of printed thermal paper rolls may look acceptable when the flexographic press starts running. The artwork is visible, the colours appear correct, and the web moves smoothly through the printing section.

But what happens after several hundred metres?

The ink begins to smear. A logo shifts towards the edge of the paper. Fine text becomes unclear, or two printed colours no longer line up correctly.

Sometimes, the printing looks fine before slitting, but defects become visible after the material is rewound into finished POS receipt rolls.

These problems can occur during the production of custom printed thermal paper rolls, particularly when printing, slitting, and rewinding are performed in one production line.

For thermal paper converters in South Africa, understanding these defects is important when handling branded receipt roll orders for retailers, restaurants, and other businesses.

The first step is identifying whether the problem originates from the paper, ink, printing plate, press settings, web handling, or downstream converting process.

Changing the machine speed or increasing printing pressure without finding the cause may only create more waste.

This guide examines common flexographic printing problems on thermal paper and explains practical checks manufacturers can perform before accepting a production batch.

flexo printer slitter rewinder

1. Why Is Thermal Paper Different From Ordinary Printing Paper?

Thermal paper is manufactured with a heat-sensitive coating that allows a direct thermal printer to produce an image without an ink ribbon.

For many custom printed thermal receipt rolls, the flexographic artwork is applied to the reverse side, while the heat-sensitive surface is reserved for transaction printing.

However, not every thermal paper has the same surface characteristics.

Some materials have different back coatings, surface treatments, moisture levels, and thermal sensitivity characteristics.

These differences can affect ink adhesion, drying, paper handling, and finished roll performance.

Before beginning flexographic printing, the converter should obtain the jumbo thermal paper’s technical specifications and confirm that the intended ink system is suitable for the printing surface.

A printing method that performs well on kraft paper or conventional uncoated paper may not produce the same result on thermal receipt paper.

For this reason, testing the intended thermal paper and ink combination is preferable to relying solely on settings used for other materials.

2. Ink Smearing After Flexographic Printing

Ink smearing is one of the defects worth checking during the manufacture of printed thermal paper rolls.

The artwork may initially appear clear, but the printed image becomes marked or transfers onto another surface as the paper passes through subsequent rollers or is rewound.

Possible Causes

Ink smearing may result from:

  • Insufficient drying before the next processing stage
  • An unsuitable ink formulation
  • Excessive ink deposition
  • Incorrect ink viscosity or printing conditions
  • Inadequate drying capacity at the operating speed
  • Contact with downstream rollers before the ink is ready for handling

The actual cause depends on the ink chemistry, paper surface, printing equipment, and production conditions.

How to Investigate the Problem

First, inspect the printed web immediately after the printing and drying section.

If the image is already smearing before slitting, the problem is likely associated with printing or drying rather than the rewinding system.

Check the ink supplier’s recommended operating conditions and verify that the drying equipment is functioning as intended.

Review the ink application and running speed.

If the printed web is acceptable before slitting but becomes marked after rewinding, inspect the downstream contact surfaces and winding conditions.

Reducing the speed for a controlled test may help determine whether available drying time is contributing to the defect.

However, lower speed alone does not establish that the ink and paper combination is suitable.

Production check: Inspect both the printed web before slitting and the finished roll after rewinding. Comparing these stages helps identify where the damage begins.

3. Poor Ink Adhesion on Thermal Paper

A printed logo may initially appear correct but rub off easily when the paper is handled.

This is different from ink smearing caused by incomplete drying.

Poor adhesion can occur even after the printed image has reached its expected drying condition.

What Can Cause Poor Ink Adhesion?

The printing surface may have properties that are unsuitable for the chosen ink.

Other possible contributors include surface contamination, an incompatible ink formulation, incorrect drying or curing, and unsuitable printing conditions.

inline-printer-750x563

Thermal paper back coatings can vary between material grades.

An ink that adheres satisfactorily to one jumbo thermal paper may not perform identically on another.

What Should the Converter Do?

Begin by confirming which side of the thermal paper is being printed.

Next, check the ink manufacturer’s recommendations for the intended thermal paper surface.

Perform an adhesion or rub-resistance test using an agreed procedure appropriate to the finished product.

If the ink fails the test, changing printing pressure is not necessarily the correct solution.

The paper and ink combination may need to be reviewed.

For manufacturers receiving regular branded thermal receipt roll orders, testing new paper grades before bulk production can help avoid problems that only become apparent after the rolls reach customers.

4. Blurred Logos and Unclear Printed Text

A printed design may lose sharpness even when the ink adheres correctly.

Small letters become difficult to read, fine lines thicken, and the edges of logos appear uneven.

In flexographic printing, several factors can contribute to this problem.

Printing Pressure

Excessive printing impression may distort fine image details.

The operator should check the impression settings and inspect whether the plate is making appropriate contact with the paper.

Increasing pressure does not automatically improve print clarity.

Printing Plate Condition

Worn, damaged, or incorrectly prepared plates may not reproduce the approved artwork accurately.

Inspect the plate for visible defects and confirm that it has been mounted correctly.

Ink Transfer

Incorrect ink transfer conditions can also affect fine details.

The operator should check the ink system, anilox condition, and settings applicable to the selected printing unit.

Artwork Preparation

Some defects originate before printing begins.

Small fonts, very fine lines, or low-quality artwork may be difficult to reproduce using the selected plate and press configuration.

The design should be reviewed before plate production.

For customers ordering return policies or other text-heavy thermal receipt printing, readability should be part of the artwork approval process.

Production check: Compare the printed sample with the approved artwork and an agreed print-quality reference. Do not judge the result only from a distance.

5. Colour Misregistration During Multi-Colour Printing

A two-colour logo should have the individual printed colours positioned correctly relative to one another.

When the colours shift, the image may show unwanted outlines, gaps, or overlapping areas.

This is known as a registration problem.

Possible Causes

Misregistration may be associated with:

  • Incorrect plate or cylinder setup
  • Unstable web tension
  • Web tracking variation
  • Printing unit alignment
  • Changes in operating conditions
  • Inappropriate registration adjustments

The extent to which these factors affect printing depends on the press construction and control system.

How to Check Registration

Start by inspecting the printed image while the press runs at an agreed stable speed.

Determine whether the registration error remains constant or changes during production.

A consistent offset may indicate a setup or alignment issue.

An error that varies during running may require further investigation of web handling, mechanical conditions, or registration control.

Check the printing plates, cylinders, web path, and relevant control settings according to the equipment manufacturer’s operating instructions.

The acceptable registration tolerance should be established according to the customer artwork and machine capability.

For custom printed thermal paper rolls with simple single-colour branding, multi-colour registration is not required. Manufacturers should avoid selecting unnecessary printing stations without considering their actual orders.

6. Incorrect Printing Repeat Length

Consider a retail customer requesting a company logo repeated along the reverse side of a thermal receipt roll.

The customer approves the artwork and expects a consistent distance between repeated images.

If the printing repeat does not match the approved design, the finished product may not meet the order specifications.

What Determines Printing Repeat?

In conventional flexographic printing, the repeat is determined by the effective circumference of the printing cylinder and its plate arrangement.

The converter should confirm the required repeat before selecting the printing cylinder and preparing the plate.

Common Problems

An unsuitable cylinder or plate arrangement may produce a repeat that differs from the required artwork specification.

If the repeat is correct but the image position varies along the web, the operator should also inspect web movement and the printing process.

Practical Checks

Measure the actual printed repeat on the paper.

Compare it with the approved production specification.

Confirm the printing cylinder, plate mounting, and appropriate press settings.

If the customer’s artwork requires a repeat outside the machine’s supported range, this limitation should be identified before accepting the order.

For South African manufacturers supplying custom printed POS rolls, checking repeat length during sample production can prevent disputes after bulk delivery.

7. Printed Artwork Moves Toward the Edge After Slitting

This problem is particularly relevant to an inline flexo printing slitting machine.

The artwork may be correctly printed on the moving thermal paper web, but after slitting, the logo appears too close to one edge of the finished roll.

In some cases, the slitting knife cuts into the printed image.

The printing unit may be operating correctly. The problem can originate from the relationship between the printed lanes and the cutting positions.

Example: Printed POS Receipt Rolls

Suppose a manufacturer receives an order for nominal 80 mm printed thermal receipt rolls.

Several artwork lanes are arranged across the width of the jumbo thermal paper.

Each printed lane must correspond to the finished cutting layout.

If the web moves laterally or the knives are positioned incorrectly relative to the artwork, the finished rolls may have unequal printed margins.

How to Investigate

Check the artwork lane layout against the approved cutting plan.

Verify the actual knife-edge positions rather than assuming that the combined blade and spacer dimensions directly establish the final paper width.

Inspect web guiding and alignment between the printing and slitting sections.

Then measure both the finished paper width and the location of the artwork relative to the cut edges.

A printed roll can meet its paper-width specification and still fail because the image position is incorrect.

Production check: Inspect finished rolls from different lanes across the jumbo paper width, not just one sample.

8. Ink Transfer and Marking During Rewinding

A printed thermal paper web may pass the initial printing inspection but develop marks after it has been wound into a finished roll.

This can happen when the printed surface contacts another layer of paper or machine components under unsuitable conditions.

What Should Be Checked?

Examine whether the ink has reached its required drying or curing condition before rewinding.

Check the winding tension and the points where the printed surface contacts rollers or adjacent paper layers.

Inspect the finished roll for unwanted ink transfer.

If marking appears only after winding, the investigation should focus on the conditions introduced after the printing section as well as the ink’s final properties.

Why Is This Important?

Printed thermal till rolls may remain packaged and stored before reaching the end user.

A roll that looks acceptable immediately after production can still develop problems if the ink, paper, and winding conditions are incompatible.

Where appropriate, finished samples should be evaluated after a representative conditioning or storage period.

The testing method should match the customer’s requirements and the ink and paper suppliers’ recommendations.

9. Why Printing and Rewinding Speed Must Be Coordinated

On an integrated line, the printing section and the downstream slitting and rewinding section must operate together.

Flexographic printing generally benefits from stable web movement.

Some thermal paper small-roll rewinders, however, use intermittent cycles when a finished roll is completed and another winding cycle begins.

The machine design must account for these different operating requirements.

How a Web Accumulator Can Help

Certain inline flexo printing slitting configurations include a web accumulator or buffer.

900A-slitter-rewinder-machine-1125x750

Looking to manufacture custom-printed thermal receipt rolls? The JT-SLT-1400P combines flexographic printing, slitting, and rewinding in one production line. It supports branded POS rolls with logos, advertising messages, and other printed artwork, subject to the printing configuration. For manufacturers planning to add printing capabilities to their converting operations, JOTA can help evaluate the required printing colours, finished roll dimensions, and production specifications.

The accumulator temporarily stores or releases a length of paper to help manage differences in web movement between the printing and rewinding sections.

The actual operating sequence depends on the machine design.

For example, when the downstream rewinding system temporarily changes speed, an appropriately designed accumulator can help accommodate the resulting web-demand difference.

It does not remove the need for correct tension control or suitable coordination between machine sections.

What Should Buyers Verify?

Before purchasing an integrated printing and slitting line, ask the equipment manufacturer to demonstrate how the system behaves during the actual roll-changing cycle.

The test should include the intended roll diameter, operating speed, and printing conditions.

A machine demonstration using only a continuously running web may not reveal how the complete line performs during intermittent rewinding operations.

10. Troubleshooting Checklist for Thermal Paper Flexo Printing

When a printing defect appears, operators should record the conditions before making adjustments.

Changing several settings at once can make it difficult to identify which factor caused the problem.

The following table provides a starting point for investigation.

Printing ProblemAreas to Check First
Ink smearingDrying conditions, ink application, running speed
Poor ink adhesionPaper surface, ink compatibility, drying or curing
Blurred artworkImpression, plate condition, ink transfer
Colour misregistrationPlate setup, web tension, alignment, registration control
Incorrect print repeatCylinder and plate arrangement
Artwork cut during slittingLane layout, web guide, knife positions
Marking after rewindingInk condition, web contact, winding tension
Variation after roll changesWeb handling, accumulator and line coordination

These are possible causes, not definitive diagnoses.

A controlled inspection should identify where the defect first appears and which operating condition changes with it.

If a defect cannot be resolved through the specified operating and maintenance procedures, the machine manufacturer and relevant ink or paper supplier should be consulted.

11. What Should Be Included in an Inline Flexo Printing FAT?

For manufacturers considering an inline flexo printing slitting machine for a South African converting factory, Factory Acceptance Testing should cover both printing quality and finished roll production.

A machine that can reproduce artwork correctly but cannot maintain acceptable slitting and rewinding quality does not necessarily meet the buyer’s production requirements.

The same applies to a slitter rewinder that runs well without printing but cannot achieve the required integrated operating conditions.

Artwork Reproduction

Use representative artwork and verify clarity, print positioning, and repeat length.

Colour Registration

For multi-colour configurations, inspect registration against the agreed acceptance requirements.

Ink and Paper Compatibility

Test with the agreed thermal paper and suitable ink system. Confirm the inspection method and acceptance conditions beforehand.

Printing and Slitting Alignment

Check the printed lanes against the finished cutting positions.

Finished Roll Inspection

Measure roll width, outside diameter, core dimensions, winding quality, and artwork placement.

Operating Speed

Record the combined printing, slitting, and rewinding speed under the agreed test conditions.

Roll Change and Web Handling

Where applicable, demonstrate rewinding cycles, accumulator operation, and the response of the integrated line.

The buyer and manufacturer should agree on FAT criteria before testing.

For complex artwork, it is advisable to send approved design files and representative material specifications in advance.

Producing Custom Printed Thermal Rolls in South Africa?

If your factory is experiencing printing quality problems or considering an integrated printing and slitting line, the production requirements should be reviewed together.

JOTA Machinery provides inline flexographic printing, slitting, and rewinding configurations for manufacturing custom printed thermal paper rolls.

Share your thermal paper specifications, printing colours, artwork repeat length, finished roll widths, and target production volume.

Our engineering team can review a suitable machine configuration for your production requirements.

Discuss Your Inline Flexo Printing & Slitting Requirements

Conclusion

Flexographic printing problems on thermal paper rolls can originate from several different parts of the production process.

Ink smearing may be associated with drying conditions, while blurred artwork may require inspection of printing pressure, plate condition, and ink transfer.

Colour registration and repeat-length problems involve different aspects of the printing system.

In an inline flexo printing slitting machine, the relationship between printing layout, web handling, cutting positions, and rewinding introduces further considerations.

For manufacturers producing custom printed thermal paper rolls, the important practice is identifying where a defect begins before changing machine settings.

A reliable production process depends on compatible materials, correctly prepared artwork, suitable printing conditions, controlled slitting and rewinding, and consistent inspection.

Looking for an Inline Flexo Printing Slitting Machine?

JOTA Machinery manufactures thermal paper slitting and rewinding equipment with inline flexographic printing configurations for custom printed POS receipt rolls and thermal till rolls.

If you’re planning to introduce custom printing or upgrade an existing thermal paper converting line in South Africa, send us your artwork and production specifications.

Our engineering team can discuss printing colours, repeat length, web handling, slitting configuration, and machine testing requirements before preparing a quotation.

Request an Inline Flexo Printing Slitting Machine Quotation

Last Updated on 19/10/2026 by Jota Machinery

Scroll to Top